Skateboard Trucks




Ace Skateboard Trucks 02 5.0 Low Raw Polished Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 03 5.375 Low Raw Polished Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 33 5.37 Rally Green Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 33 5.375 Copper Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 33 5.375 Diamond Teal Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 44 5.75 Matte Black Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 44 5.75 Rally Green Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 55 6.37 Rally Green Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 55 6.375 Shelby Blue Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Ace Skateboard Trucks 66 6.75 Shelby Blue Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Bullet Skateboard Trucks Black 140mm Set Of 2 Trucks

Set of 4 wheels.

All-Terrain Formula™ (ATF) wheels are poured in a special soft urethane we call All-Terrain Formula or (ATF). ATF wheels are excellent for rougher terrain so regardless of road quality, this revolutionary formula will roll you there quickly and smoothly.

Bullet Skateboard Trucks Black 150mm Set Of 2 Trucks

Box includes front and rear truck. Mounting hardware and riser pads.

- 2 7/8” tall
- 6.5” hanger with a 9” axle
- .55’ top conical bushing, .65” bottom conical bushing. Stock 89a durometer for easy pumping, optional 95a durometer set available
- 2 ½” kingpin
- .7” OD x ½” ID pivot cup
- Drilled to new and old school mounting patterns
- Sand cast 356 aluminum alloy, medical heat-treated to Rockwell T6
- Made in the USA

The Carver CX.4 is brand new for 2013. We’ve made significant improvements to this front-only truck that gives it unprecedented thrust and pump, as well as increased turn radius and snap-back. With a few carves side to side you immediately begin to generate speed, and with a little more pumping you can gain significant speed. The thrust generated is so powerful you can even pump uphill. So whether you’re surfing the sidewalk, flowing through a skatepark or big-wave surfing downhill, you never have to put your foot down to make a section. For years many longboard companies have falsely claimed that their boards ‘feel just like surfing’, but we took that promise seriously. So while the CX may just look like a regular RKP (Reverse King Pin) style truck, the simple appearance of this patented surfkate hides its true performance. What you get is a truck that has all the thrust of a surfboard but with a lighter and more stable pushing platform. While these two properties would seem contradictory, through a careful pairing of both the thrust-prone geometry and a sculpted bushing cup that hugs the urethane bushings in just the right way, you get a truck that is both loose when you want to pump and stable when you want to push or land tricks. Plus without the swiveling arm of our C7 surf truck, the CX is both lighter and easier to ride fakie, opening up your ability to perform tricks involving reverse riding like 180 slides while still feeling that reverse-riding-surfboard feel.

Thrust

The secret ingredient in the CX performance is the thrust you get with each pump and carve. You can see the extreme turn angle of the hanger, and what this gives you is more turn at the nose compared with the tail (check out the C2 rear truck tech specs page for comparison)This creates the same dynamic you get with a surfboard, where you pivot your turns from the tail. We tilted the overall geometry of the previous CX.3 by 3 degrees, essentially wedging the whole truck and sharpening the turn angle. We’ve also raised the bushing seat, and increased the height of the bottom bushing to .65” so each turn creates more hanger projection to the side, essentially pushing you forward with every carve. This new bottom bushing set up, paired with a top bushing of .55”, makes them interchangeable with all current RKP bushing sets. Plus with more clearance under the hanger you can even use double barrel bushings with a flat washer for the most combinations of aftermarket customization ever.

Height

We increased the height of the CX baseplate so you can use 70 mm Roundhouse wheels and get the full tilt during deep carving while still controlling wheelbite. This has reduced the number of 3/16” risers used on lower models from 3 to 1, so if you ride a 70 mm wheel you only need one riser. If you ride our smaller 65 mm Roundhouse wheels you can eliminate any risers and still get full range turning without wheelbite. The reduction of 2 risers eliminates their added weight, plus it shortens the mounting hardware. With longer hardware you get some baseplate twisting as your truck turns, reducing the direct forces on the truck and increasing wear on the wood deck around the screw heads. Shorter hardware provides a more secure and longer lasting mount. Whenever you use aftermarket wheels though, always check for full turn range and use as many risers as you need to prevent bite.

Precision Pin

The key to the smooth and effortless action of this truck literally pivots on the machined pivot pin. The precisely polished pin fits the pivot cup perfectly so there’s no side-to-side dance or restrictive binding, either of which compromises performance. We put a dab of grease on the pivot so it rotates effortlessly, so all you feel is the resilient rebound of the urethane bushings. Further, this polish eliminates pivot cup wear, giving you long-lasting performance. Beyond just a pivot pin, this joint now acts just like a thrust bearing, but without the added weight, complexity or cost of needle bearings.

Mounting

Because the CX is a Reverse King Pin (RKP) front truck, the kingpin faces forward when the truck is mounted to the nose. This is the opposite of the rear C2 truck, which is a Standard King Pin (SKP) truck. Since this is a directional set up like a surfboard, the advantage of this is that both front and rear axles are trailing behind the kingpins, reducing the propensity for leading-axle induced wobbles. Further reducing this tendency is the differential between the front and back turn rates. This is because as the front turns more sharply, the rear has a more moderate rate of turn and acts as a sort of rolling rudder that stabilizes the board at higher speeds.

History of the Carver CX Truck

So for the past 16 years we’ve subscribed to the philosophy of Kaizen, or continuous improvement. So for the past 9 years we’ve continued to work on ways to make each new version of this truck perform better than the last. With this latest version, the CX.4, we’ve boosted the performance of this truck to have an amount of thrust none of us ever thought possible. Here’s the history of this incredible truck:

Caliber Longboard Trucks 2 184mm 44 Degrees Raw

Features:

Diameter:61mm
Durometer: 78a
Hub: Center set
Contact Patch: 32mm

Caliber Longboard Trucks 2 184mm 44 Degrees Satin Green

Hardcore Bushings feature the SkateOne™ patented bonded insert technology that will transform your trucks into high performance carving, racing, or freeride machines. The bonded insert will noticeably reduce slop, create a more fluid turn, add stability, and allow you to run a lower durometer bushing in your truck than normal. The insert locks your steering axis in without any extra parts and ensures you only compress the bushing top and bottom rather than open it like an elastic band. 

ZERO BREAK IN 

85a - Softest - For carving, cruising, freeriding, or those who want quick steering trucks. 
88a - Medium Soft - For carving, cruising, freeriding, or DH. This is the team's choice by far.
90a - Medium - For carving, freeriding, or DH. 
93a - Hard - For freeriding, DH, or heavier riders who want more support. Perfect for low angle rear trucks. 

Carver Skateboard Trucks C5 Surf Trucks Silver

Quality for your money deck from Absolute Distributors Australia.

9" wide x 32" long

Specifications:

Canadian Maple
7 Ply standard lay up veneer
Laser Etched sizing

NOTE: Picture is for shape reference only. Correct colour is in title.

Carver Skateboard Trucks Cx 6.5 Surf Trucks Silver

Quality for your money deck from Absolute Distributors Australia.

9" wide x 32" long

Specifications:

Canadian Maple
7 Ply standard lay up veneer
Laser Etched sizing

NOTE: Picture is for shape reference only. Correct colour is in title.

Gullwing Charger Skateboard Trucks 10" Vapor Pair

Independent Trucks is the #1 choice of professional skateboarders since 1978 and “Built to Grind”! Skateboarding’s most iconic brand and leading manufacturer of skateboard trucks, hardware, clothing, and accessories.


INDEPENDENT SIZE CHART:


- 109 for 6.9" to 7.2" decks

- 129 for 7.4" to 7.8" decks

- 139 for 7.8" to 8.25" decks

- 144 for 8.1" to 8.5" decks

- 149 for 8.25" to 8.65" decks

- 159 for 8.6" to 9" decks

- 169 for 9" - 10.5"" decks

- 215 for 10.5" and up decks

Gullwing Reverse Truck 10 Royce Pro Pair

Gullwing Reverse Truck 10 Royce Pro Pair

$109.99
RRP $119.99
SAVE $10.00 (8%)

One set of longboard trucks from Rare Board Co

Independent Skateboard Trucks 139 Hollow Lopez Silver Set Of 2 Trucks

Specifications:

  • Width - 8.0"
  • Length - 31.7"
  • Wheelbase - 14"